• Rejected or didn't receive your confirmation email? Hit the Contact Us link at the bottom of any page to send us a message. We'll get you sorted. ~Jerk

Chopping up a perfectly good fuel tank

BlackdogADV

Well travelled
I haven’t jumped into this rabbit hole just yet. Ever since I bought my bike I’ve always wished for more fuel capacity and a nicer fuel cap. I just found this tank for a fair price, it will be my starting point.
Plan is to increase capacity by a gallon and install a Triumph or HD fuel cap with appropriate metal.
Perfect winter project.
 

Attachments

  • IMG_3926.png
    IMG_3926.png
    1.2 MB · Views: 19
I haven’t jumped into this rabbit hole just yet. Ever since I bought my bike I’ve always wished for more fuel capacity and a nicer fuel cap. I just found this tank for a fair price, it will be my starting point.
Plan is to increase capacity by a gallon and install a Triumph or HD fuel cap with appropriate metal.
Perfect winter project.
This might interest you...
Expanded fuel tank
 
Good luck with that - your welding skills must be very good 👍
I've been looking for an alloy tank similar to the GT but bigger - it's so narrow, it could hold another 50% or more!
I'm surprised there isn't a little sweat shop in India knocking them out.
Please keep us posted with lots of pics 👍
 
I would like to have a fuel cap that was hinged to the tank. As it is I must look for a clean place to set the cap during refueling. Usually use a paper wipe from the station and set it all on the ground.

If range between fuel stations is your concern there are a number of carry-with gasoline storage containers available. Capacities range from about 30 oz through about 4 gallons, and anything in between. Cost is cheap.
 
If you have removed your EVAP system, as many have, and want to squeeze out a few more ounces of volume available in your OEM tank: I would convert your gas cap to a venting cap instead of sealed as the OEM is. Should be as simple as 1 or 2 tiny holes (1/64") drilled in the cap, being careful not to hit anything important like the cap spring/lock mechanism. This assumes your tank vent line, lower right rear metal tube exiting tank, has been sealed closed.
 
Good luck with that - your welding skills must be very good 👍
I've been looking for an alloy tank similar to the GT but bigger - it's so narrow, it could hold another 50% or more!
I'm surprised there isn't a little sweat shop in India knocking them out.
Please keep us posted with lots of pics 👍
Check out Omega Racer!
 
I don’t have the tank yet, I found it on FB marketplace for $50 but I’ll have to add shipping to that. Anyway this is my tank that I intend on leaving stock. I’ll be cutting the orange tank about where the pin strips are on my tank. I’ll add 1” to 1.5” of height to it. I’ll also replace the fuel cap opening with one from a Triumph.
 

Attachments

  • IMG_3929.jpeg
    IMG_3929.jpeg
    287.1 KB · Views: 7
I don’t have the tank yet, I found it on FB marketplace for $50 but I’ll have to add shipping to that. Anyway this is my tank that I intend on leaving stock. I’ll be cutting the orange tank about where the pin strips are on my tank. I’ll add 1” to 1.5” of height to it. I’ll also replace the fuel cap opening with one from a Triumph.
I'm sure you have it covered ... but ... make sure that Triumph cap doesn't rely on tank mounted "tanks".
Places like Summit Racing and Amazon have a selection of caps. A number of the ER guys have done the Monza style keyless units. They used the "weld-on" sleeve but used JB Weld. That was years ago and no reports of failure.
 
I'm sure you have it covered ... but ... make sure that Triumph cap doesn't rely on tank mounted "tanks".
Places like Summit Racing and Amazon have a selection of caps. A number of the ER guys have done the Monza style keyless units. They used the "weld-on" sleeve but used JB Weld. That was years ago and no reports of failure.

I am one of those. Still working great!

Replaced keyed fuel cap with a Monza setup. Using a MON25X and a COLA25 from B.A.T. Inc.

62B82820-BF0B-42B6-BEF6-6E4607E542AB.jpeg
 
Last edited:
Wow - 18 litre and fit with standard seat - sorely tempted - the only issues are the £600 price and the import duties on top ☹️
Can't justify that while the existing tank isn't leaking 🙄

Some cool parts!!!
 
Good idea on the tank, adding capacity but still allowing it to fit to the frame and seat.

But, are you doing anything with the fuel level sensor? Like with the stock tanks, will show full for a lot of miles then droppinq quickly. Or is that even a concern?

FWIW, I have an extra fuel tank I'd part with, the original flat black and turquoise version. Same financial deal as here if anyone is interested. Located in the SE metro area of Phoenix.
 
Top Bottom